FrankenXenon

The following page is for reference only!

The directions on the page could cause irreparable damage to your PowerMac G5 if not followed correctly. By continuing on this page, you agree and understand that xenonwiki.com is not responsible for any damages and that absolutely no warranty is offered with these instructions.

This page is for research and educational purposes only. The software and information linked is not to be used for commercial purposes. By continuing on this page, you agree to use any listed information or software/ROMS for NON-PROFIT use only!

You have been warned!

PowerMac G5 Models

PowerMac G5 A1047 PCI-X

The original Alpha PowerMac G5 model used was the A1047 Dual-Processor 2.0GHz PCI-X model. This is the last model to ship with the PowerPC 970 CPU since they switched to the 970fx in the PCI-X 2 model. The Dual-Processor is not to be confused with the Dual-Core configuration. Dual-Processor is two physical CPUs with 1 core each for a total of 2 cores. Dual-Core is 1 physical PowerPC 970MP with 2 cores.

PowerMac G5 A1047 PCI-X 2 CPU Cover

If you are searching item listings for the correct model, look for the one with 2 G5 markings. If the heatsink baffle is one single piece with dual G5 markings then it's PCI-X 2 which is also supported. If it's one large baffle with a single G5 marking then it's a later PowerPC 970MP Dual-Core or Quad-Core model. PowerPC 970MP systems use a different SMC and should be avoided due to their unknown compatibility.

Later PowerMac G5 PCIe Model

Currently, the only known supported model is the A1047 PCI-X and PCI-X 2 as they have 64bit PCI slots and support AGP graphics. The later non-PCI-X models are PCI Express and don't use the U2 System Management Controller (SMC).

The motherboard revision of your PowerMac G5 does not matter as long as it is a PCI-X or PCI-X 2 A1047 model.

The BootROM version of your motherboard does not matter as long as the rest of the hardware matches. The Xenon Operating System has been tested on BootROMs as late as 5.1.8f7.

Processor

A 2.0GHz Dual Processor configuration is required. Both the PowerPC 970 from PCI-X models and the PowerPC 970fx from PCI-X 2 models are compatible.

Processor configurations clocked faster than 2.0GHz will not boot the Xenon OS. Also, faster clocked PowerMac G5 PCI-X and PCI-X 2 models were liquid cooled with a system that was prone to leaking.

Memory

512MB (2x256) minimum of DDR3 400MHz PC3200 is required. The PowerMac G5 has 8 RAM slots for a total maximum capacity of 8GB.

The XenonOS will still boot if you have more than 512MB of RAM.

Hard Drive

The Alpha PowerMac G5 shipped with a stock 160GB SATA 7200RPM Seagate ST3160023AS drive. A specific drive size or model is not required as long as it is SATA.

Any SATA drive over 40GB should work.

The PowerMac G5 uses screws with rubber caps to mount the drive in the chassis. You may need to source these if your PowerMac G5 did not come with a hard drive.

Network Card

The network card in the Alpha PowerMac G5 is an Intel Pro100+ 100Mbps PCI 741462-010. Other similar network cards will work as long as they are PCI, Intel based and not PCIe.

Confirmed working network cards:

Intel Pro/100+ 100Mbps PCI 741462-010
Intel Pro/100S 100Mbps PCI 751767-004

A network card is not required for XenonOS to boot. It is only required for network use such as Xbox Neighborhood.

The built-in Gigabit ethernet port on the PowerMac G5 motherboard is not recognized by XenonOS. The original Alpha PowerMac G5s had this port taped over.

Optical Drive

An IDE DVD-ROM drive is required for the Xenon OS to boot. If you are using a PC flashed graphics card that requires external power then you will need a molex Y splitter to split power off of the DVD drive's power cable. If the DVD drive is unplugged or not present then the Xenon OS will fail to boot.

Display

Higher resolution displays have been known to not work. This includes all ADC based Apple Cinema Displays. If you are encountering an issue with a black screen on boot (or the machine hanging) try switching to a VGA based low resolution display.

Graphics Card

For the 1529 hard drive image, an R420 based card like the X800 XT is required. See the below section on sourcing a compatible video card.

X800 XT Alternatives

The ATI Radeon X800 XT Mac Edition card is a rare one to come across. It's even rarer to find one for sale in working condition due to the age and heat generated by the cards. Luckily, ATI released many different R420 cards using the same chip that are able to be flashed with the X800 XT ROM.

It's important to note that Mac edition cards are different in the following ways:

They have an ADC connector to support Apple displays
They have a 128KB ROM as opposed to a 64KB PC ROM (Although the PC X800 Pro was also 128KB)
They have an extra connector on the bottom of the card to provide extra power without needing an external power connection

Most PC ATI R420 based cards require an external molex power connection since the AGP slot isn't able to provide enough power. You will need to purchase an appropriate molex Y splitter in order to split power from the PowerMac G5's DVD ROM drive.

Do NOT try to connect a graphics card without the appropriate power connections! You might damage your card or PowerMac G5. If you hear your card chirping or whining then double check your power connections. Some cheaper Chinese molex y splitters have flaky or loose connectors.

If you find any references online regarding taping pins 3 and 11 of the GPU or removing resistors, this is only required when forcing the card into AGP x4 mode for use in a PowerMac G4. The PowerMac G5 supports AGP x8 and does not need this modification.

Be aware that many online Mac parts stores list the ATI Radeon X800 XT Mac Edition as being in stock but will put your order on hold and tell you that the item is discontinued or out of stock. Avoid these sites if possible.

Refer to the graphics card information table below on what specific graphics cards are currently known to be supported.

Graphics Card Info Table

Model	Part Number	DeviceID	ASIC P/N	GPU Clock	Memory Clock	EEPROM	VRAM	ROM Size	Status	Symptoms	Next Steps
ATI X800 XT Mac Edition	109-A35803-00	4A48	215RADCGA12F	475 MHz	500 MHz	PMC 25LV010	Samsung K4J55323QF-GC20	128KB	WORKING	Working with stock X800 XT ROM
ATI X800 XT Mac Edition (Engineering Sample)	109-A35803-00	4A48	215RADCGA12FS	475 MHz	500 MHz	PMC 25LV010	Samsung K4J55323QF-GC20	128KB	WORKING	Working with stock X800 XT ROM
ATI FireGL X3	109-A30101-00	4A4D	215RADCGA11F	492 MHz	450 MHz	ST 25P05VP	Samsung K4J55323QF-GC20	64KB	WORKING*	Working with Tome's reduced ROM. Shows slight artifacting.
	109-A30131-10	4A48	215RADCGA12F	492 MHz	450 MHz	ST 25P05VP	Infineon HYB18T256324F-20	64KB	UNSTABLE	Boots with modified 128KB EEPROM, shows artifacts due to slower Infineon VRAM	Lower core/memory clock speeds to 492/450. Tome's reduced 64KB ROM works.
		4A4D	215RADCGA11F	492 MHz	450 MHz	ST 25P05VP	Samsung K4J55323QF-VC20	64KB	WORKING*	Working with Tome's reduced ROM. Same card as 109-A30131-00 but with different ASIC
ATI Radeon X800 Pro	109-A26100-00	4A49	215RADCGA11F	475 MHz	400 MHz	ST 25P05AV	Samsung K4J55323QF-GC20	128KB	INCOMPATIBLE	Boots into recovery installer (but not OS) with modified X800 XT ROM	Try adjusting core/memory clock speeds
ATI Radeon X800 XT All-in-Wonder	109-A38304-20	4A4B	215RADCGA11F	500 MHz	500 MHz	PMC 25LV512	Samsung K4J55323QF-GC16	64KB	INCOMPATIBLE	Not Mac compatible due to the built-in TV tuner	Attempt using a different DeviceID

"*" Denotes a card that is mostly working but might show slight artifacting in some applications such as Dolphin and SceneViewer.

Preparing a Mac compatible ROM for your Graphics Card

Most of the following ROMs were obtained from The Mac Elite.

When you are choosing a ROM for your graphics card, it is important that you choose one that matches your EEPROM size and device ID. All Mac ROMs are 128KB by default.

If you do not want to replace your EEPROM chip, then you can use a "reduced ROM" which will fit on a 64KB EEPROM. The only difference with these ROMs is that they will not boot into OSX without the ATI Display Drivers being installed. The Xenon OS will boot properly with a 64KB reduced ROM.

Before flashing your graphics card, backup your original ROM by using the ATI Multi Dumper instructions below. Note the device ID listed in the .txt file generated by the program as it will need to match your chosen ROM. You can also refer to the Graphics Card Information Table to confirm the device ID that corresponds with your ASIC model.

To modify/verify the device ID set in the chosen ROM, open it in a hex editor such as HxD and look for the following fields. Since the ROM is little-endian, the two hex values are backwards. 4D 4A is actually device ID 0x4A4D. Replace the two occurrences with your proper device ID (in little-endian format) if needed and save the ROM

Flashing your Graphics Card

Flashing your Graphics Card can be done a few different ways. The most reliable way is to use the PowerMac itself and the ATI multi-flasher utility.

This method requires that you have Mac OS 10.4.11 installed on your PowerMac G5. It is recommended to install any Java updates from Software update since part of the utility is Java based. Avoid any firmware updates offered by Software Update.

BEFORE installing your PC flashed Graphics Card and AFTER installing Mac OS 10.4.11, enable VNC control in order to remotely control your machine since the internal graphics card will be inoperable until it is flashed.

Open System Preferences
Go to the Networking pane and note down your machine's IP address
Go to the Sharing pane and enable Screen Sharing
Also enable Remote Login on the Sharing pane
With Screen Sharing selected, click Access Privileges on the right section of the panel
Enable all remote control options and set a VNC password
Download a VNC client such as TightVNC on a remote machine, test that everything works before moving forward
Enable Safe Mode by running the following command in Terminal sudo nvram boot-args="-x"
1. Enabling Safe Mode will help prevent the machine from crashing on bootup with a PC-flashed card

You can now install your PC Graphics Card. If your card has extra power requirements, ensure that they are connected.

After booting your Mac with the PC-flashed graphics card, connect to your Mac via VNC
1. If you receive a "Connection Refused" error, try resetting the VNC server via SSH with the following command sudo /System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Resources/kickstart -restart -agent
Download the latest version of Graphiccelerator from Thomas Perrier's website http://thomas.perrier.name/software/Graphiccelerator-1.3.4.dmg.zip and extract the contents to your desktop
Download your desired ROM to the desktop
Run the Graphiccelerator app and select Misc -> Install Mac ROM in ATI Flasher
1. The first file dialogue will ask you to select your downloaded ROM file
2. The second file dialogue will ask you to select your flasher. Select the ATI Multi Flasher under the ATI Tools folder.
3. If a warning appears saying that "This flasher already contains a ROM which will be overwritten", select OK.
Open the ATI Tools folder and launch the "Run Me First" app, it will ask for an administrator password.
First, backup your current ROM by running the ATI Multi Dumper tool
1. If the application opens and immediately closes without dumping the ROM, try launching the "Run Me First" application again.
2. The ATI Multi Dumper should place a .rom and .txt file in the ATI Tools folder, make sure that both of these files are stored safely and backed up
When you are ready, run the ATI Multi Flasher tool in order to flash your Graphics Card. It will ask for multiple confirmations before continuing.
1. Just like the ATI Multi Dumper, if it closes immediately then try running the "Run Me First" application again.

Your graphics card is now flashed. Try rebooting to see if the card now works.

Flashing the BootROM

Flashing or modifying your PowerMac G5's BootROM is NOT required for normal use.
The following information is for reference purposes only and should only be followed by experienced users!

The PowerMac G5 A1047 BootROM is stored on a 1MB AMD AM29LV008BB 40 pin TSOP. Flashing any BIOS or BootROM will always have inherited risks. If the flash is unsuccessful or corrupted then your machine will not boot after it shuts down. The only way to recover would then be to de-solder the chip and use an external programmer to reflash it. Always backup your BootROM FIRST and only flash trusted ROM files.

FlashROM for PowerPC can be used to read or write to the BootROM without an external programmer. It must be run within a linux environment and will not work within Mac OS X.

There have been some reported problems booting into LUbuntu using some Nvidia based graphics cards. This process has been tested on an ATI Radeon 9600 card that came stock with most A1047 models.

Download LUbuntu 16.04 and burn the ISO to a DVD - http://cdimage.ubuntu.com/lubuntu/releases/16.04.1/release/lubuntu-16.04-desktop-powerpc.iso
Press and hold the power button on the PowerMac G5 until you hear a long beep followed by the startup chime
1. This places the machine in Programmers Mode and will automatically place you at the OpenFirmware prompt. The BootROM cannot be read/written to without the machine being in Programmers Mode.
Insert the LUbuntu 16.04 DVD in the machine. Use the eject cd command to open the DVD tray if it was not already inserted beforehand.
Boot to the CD using the command boot cd:\\:tbxi
When prompted with the yaboot bootloader, you can either wait for it to load automatically or use the live command to continue booting to the LiveCD
1. Booting the machine fully may take a few minutes. The screen may turn off several times during this process.
Once you reach the desktop, use the terminal (CTRL-ALT-T) to download FlashROM and setup your environment
1. cd Desktop to have all the files on your Desktop instead of the home folder
2. Download FlashROM for PowerPC from dosdude1's website wget http://dosdude1.com/files/flashromppc.zip
3. Extract the flashromppc.zip file by double clicking it and pressing Extract.
Run FlashROM
1. sudo ./flashrom without any arguments will test if FlashROM can identify your BootROM. If it cannot see or read your BootROM, ensure that your machine is in Programmers Mode.
2. If you are attempting to READ/DUMP your BootROM, run sudo ./flashrom -r 1.bin which will create a 1MB .bin file called 1.bin on the desktop. This can then be transferred off of the machine using the web browser or by being SCPed to another linux machine
3. If you are attempting to WRITE to your BootROM, download the ROM to your desktop and run sudo ./flashrom -w ./NAME OF ROM FILE to write it
  1. The ROM file MUST be 1MB in size in order to be written. Not larger or smaller. Do NOT try to force a smaller/larger ROM onto a chip that doesn't support it!
  2. Optionally, you can verify the BootROM's contents against the ROM you were trying to flash to see if it was successful by running sudo ./flashrom -v ./NAME OF ROM FILE

Controllers

Similar to a final XDK, XenonOS does not recognize any USB keyboards or mice within XShell.

The system is controlled either remotely via the Xbox 360 SDK or by using a wired Xbox 360 controller since it doesn't have a built in RF board.

The controller MUST be wired and not just a wireless controller with a play-and-charge cable. Prototype Krypton controllers will also work.

Troubleshooting

When loading the recovery, the PowerMac G5 hangs and runs it's fans at full speed

This is a sign that the hypervisor failed to load. This usually means that your hardware configuration is incorrect.

The PowerMac G5 will run it's fans at full speed if the machine fails to load any program. Another sign of this state is if the machine requires the power button to be held down in order to shut down. The Xenon OS should shut off immediately if the power button is pressed without the need to hold it down.

Solution: Verify that your hardware configuration including CPU clock speed, number of CPUs, RAM, GPU model and DVD drive are all connected and correct. If the error still persists, reset your PRAM.

The recovery fails to install to my hard drive

Solution: Ensure that your hard drive is in the upper drive bay (labelled A) and is of sufficient capacity.

I have swapped display connections and now the PowerMac G5 only displays a black screen

Solution: Reboot the PowerMac G5. Switching video connections requires a cold reboot.

The PowerMac G5 emits three short tones on startup and refuses to boot

Solution: Ensure that your RAM is seated properly. Check for a damaged RAM DIMM.

I can't load the recovery despite having a correct hardware configuration

Solution: Try replacing your DVD drive or verifying that your optical drive's IDE ribbon cable is seated correctly. Optical drives of this age sometimes die.

The PowerMac G5's fans run at full speed and a red LED is on inside the case

The PowerMac G5 requires a clear plastic air deflector in order to direct airflow. Without the deflector installed, the fans will run at full speed when the machine is turned on. It can run with the aluminum side panel removed as long as this plastic air deflector is in place.

Solution: Install the side air deflector.